Mounting memory stick with Clie TG50

[Wong Khai Thye]

Hi,

Has anyone had any success with mounting the memory stick using "MS
Import" on the Sony Clie PEG-TG50?

On my system, I have the following errors in /var/log/messages when I
try run "MS Import":

-----------------------
Sep 26 18:27:15 cm147 kernel: hub.c: new USB device 00:02.0-1, assigned
address 4
Sep 26 18:27:15 cm147 kernel: usb.c: USB device 4 (vend/prod 0x54c/0xd9)
is not claimed by any active driver.
Sep 26 18:27:19 cm147 /etc/hotplug/usb.agent: Setup usb-storage for USB
product 54c/d9/1
Sep 26 18:27:19 cm147 kernel: Initializing USB Mass Storage driver...
Sep 26 18:27:19 cm147 kernel: usb.c: registered new driver usb-storage
Sep 26 18:27:19 cm147 kernel: scsi1 : SCSI emulation for USB Mass
Storage devices
Sep 26 18:27:19 cm147 kernel: Vendor: Sony Model: CLIE
MGMS Rev: 1.00
Sep 26 18:27:19 cm147 kernel: Type:
Direct-Access ANSI SCSI revision: 02
Sep 26 18:27:19 cm147 kernel: Attached scsi removable disk sda at scsi1,
channel 0, id 0, lun 0
Sep 26 18:27:19 cm147 /etc/hotplug/scsi.agent: sd_mod allready loaded
Sep 26 18:27:19 cm147 kernel: SCSI device sda: 63424 512-byte hdwr
sectors (32 MB)
Sep 26 18:27:19 cm147 kernel: sda: Write Protect is off
Sep 26 18:27:19 cm147 kernel: /dev/scsi/host1/bus0/target0/lun0: p1
Sep 26 18:27:19 cm147 kernel: USB Mass Storage support registered.
Sep 26 18:27:19 cm147 /etc/hotplug/usb.agent: Module setup usb-storage
for USB product 54c/d9/1
Sep 26 18:27:19 cm147 /etc/hotplug/usb/usb-storage: Load scsimon
Sep 26 18:27:19 cm147 /etc/hotplug/usb/usb-storage: scsimon allready
loaded
Sep 26 18:27:19 cm147 kernel: SCSI device (ioctl) reports ILLEGAL
REQUEST.
Sep 26 18:27:19 cm147 kernel: SCSI device sda: 63424 512-byte hdwr
sectors (32 MB)
Sep 26 18:27:19 cm147 kernel: sda: Write Protect is off
Sep 26 18:27:19 cm147 kernel: /dev/scsi/host1/bus0/target0/lun0: I/O
error: dev 08:00, sector 0
Sep 26 18:27:19 cm147 kernel: I/O error: dev 08:00, sector 0
Sep 26 18:27:19 cm147 kernel: I/O error: dev 08:00, sector 63416
Sep 26 18:27:19 cm147 kernel: I/O error: dev 08:00, sector 63416
Sep 26 18:27:19 cm147 kernel: I/O error: dev 08:00, sector 0
Sep 26 18:27:19 cm147 kernel: I/O error: dev 08:00, sector 0
Sep 26 18:27:19 cm147 kernel: ldm_validate_partition_table(): Disk read
failed.
Sep 26 18:27:19 cm147 kernel: I/O error: dev 08:00, sector 0
Sep 26 18:27:19 cm147 kernel: I/O error: dev 08:00, sector 2
Sep 26 18:27:19 cm147 kernel: SCSI device (ioctl) reports ILLEGAL
REQUEST.
Sep 26 18:27:19 cm147 kernel: SCSI device sda: 63424 512-byte hdwr
sectors (32 MB)
Sep 26 18:27:19 cm147 kernel: sda: Write Protect is off
Sep 26 18:27:19 cm147 kernel: /dev/scsi/host1/bus0/target0/lun0: I/O
error: dev 08:00, sector 0
Sep 26 18:27:19 cm147 kernel: I/O error: dev 08:00, sector 0
Sep 26 18:27:19 cm147 kernel: I/O error: dev 08:00, sector 63416
----------------------------

My system is Mandrake Linux 9.1 with kernel 2.4.21-0.13mdk. Hotsync
works normally, and I can sync with both jpilot and evolution.

My old PDA is a Clie T615 and I can definitely mount the memory stick
normally on this linux box. Also, I can still mount the memory stick
using my sony digicam, so it can't be a faulty memory stick.

Regards,
Khai-Thye.


_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Clié and Linux Homepage:
http://kreucher.net/clie/

[Alexandre Aractingi]

Post by Wong Khai Thye
Hi,
Has anyone had any success with mounting the memory stick using "MS
Import" on the Sony Clie PEG-TG50?

I have seen this kind of errors with my Sony Digicam and my Mandrake
9.1. When reporting it on the USB list, I was told that the new 2.6
kernel was supposed to solve this (but I was too lazy to test it back
then :-)).
So I don't really have the answer, but maybe you should give it a try...
--
Alexandre Aractingi <***@libertysurf.fr>

_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Clié and Linux Homepage:
http://kreucher.net/clie/

[Bill Sheppard]

Post by Wong Khai Thye
Has anyone had any success with mounting the memory stick using "MS
Import" on the Sony Clie PEG-TG50?

As far as I know, no one has yet successfully mounted a memory stick
from a Sony OS5 device. There are some good discussion threads about
this on www.cliesource.com in the Clie Linux group (back six months or
so, maybe more).

Bill
--
-------------------------------------------------------------------------
Bill Sheppard Industry Marketing Manager, Digital TV
***@sun.com Software Systems Group
[phone] (x68154) Sun Microsystems, Inc.



_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Clié and Linux Homepage:
http://kreucher.net/clie/

[Eric Laly]

Post by Wong Khai Thye
Hi,
Has anyone had any success with mounting the memory stick using "MS
Import" on the Sony Clie PEG-TG50?
On my system, I have the following errors in /var/log/messages when I

works fine for me with a 2.4.21-ac4 kernel on a Debian sid:

Sep 26 18:42:01 Bragon kernel: scsi3 : SCSI emulation for USB Mass
Storage devices
Sep 26 18:42:01 Bragon kernel: Vendor: Sony Model: CLIE MGMS
Rev: 1.00
Sep 26 18:42:01 Bragon kernel: Type: Direct-Access
ANSI SCSI revision: 02
Sep 26 18:42:01 Bragon kernel: Attached scsi removable disk sdd at
scsi3, channel 0, id 0, lun 0
Sep 26 18:42:01 Bragon kernel: usb-uhci.c: interrupt, status 3, frame#
1968
Sep 26 18:42:01 Bragon kernel: SCSI device sdd: 63424 512-byte hdwr
sectors (32 MB)
Sep 26 18:42:01 Bragon kernel: sdd: Write Protect is off
Sep 26 18:42:01 Bragon kernel: sdd: sdd1

...

Post by Wong Khai Thye
My system is Mandrake Linux 9.1 with kernel 2.4.21-0.13mdk. Hotsync
works normally, and I can sync with both jpilot and evolution.

works fine with jpilot.

Post by Wong Khai Thye
My old PDA is a Clie T615 and I can definitely mount the memory stick
normally on this linux box. Also, I can still mount the memory stick
using my sony digicam, so it can't be a faulty memory stick.
Regards,
Khai-Thye.

Regards.
Eric Laly.

_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Clié and Linux Homepage:
http://kreucher.net/clie/

[Jason 'vanRijn' Kasper]

Post by Eric Laly

Post by Wong Khai Thye
Hi,
Has anyone had any success with mounting the memory stick using "MS
Import" on the Sony Clie PEG-TG50?
On my system, I have the following errors in /var/log/messages when I

Sep 26 18:42:01 Bragon kernel: scsi3 : SCSI emulation for USB Mass
Storage devices
Sep 26 18:42:01 Bragon kernel: Vendor: Sony Model: CLIE MGMS
Rev: 1.00
Sep 26 18:42:01 Bragon kernel: Type: Direct-Access
ANSI SCSI revision: 02
Sep 26 18:42:01 Bragon kernel: Attached scsi removable disk sdd at
scsi3, channel 0, id 0, lun 0
Sep 26 18:42:01 Bragon kernel: usb-uhci.c: interrupt, status 3, frame#
1968
Sep 26 18:42:01 Bragon kernel: SCSI device sdd: 63424 512-byte hdwr
sectors (32 MB)
Sep 26 18:42:01 Bragon kernel: sdd: Write Protect is off
Sep 26 18:42:01 Bragon kernel: sdd: sdd1
...

and you have a Clie TG50, running Palm OS 5?
--
,-----------------------------------------------------------------//
| Jason 'vanRijn' Kasper :: Numbers 6:22-26
`
| All brontosauruses are thin at one end, much MUCH thicker
| in the middle, and then thin again at the far end. That is
| the theory that I have and which is mine, and what it is too.
,
| bash$ :(){ :|:&};:
`----------------------//


__________________________________________________________________________
Disclaimer: This e-mail message is intended only for the personal use of
the recipient(s) named above. If you are not an intended recipient, you
may not review, copy or distribute this message. If you have received this
communication in error, please notify us immediately by e-mail and delete
the original message.
This e-mail expresses views only of the sender, which are not to be
attributed to Rite Aid Corporation and may not be copied or distributed
without this statement.

_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Clié and Linux Homepage:
http://kreucher.net/clie/

[Eric Laly]

Post by Wong Khai Thye

Post by Wong Khai Thye
Hi,
Has anyone had any success with mounting the memory stick using

"MS

Post by Wong Khai Thye
Import" on the Sony Clie PEG-TG50?
On my system, I have the following errors in /var/log/messages

when I

...

Post by Wong Khai Thye

...

and you have a Clie TG50, running Palm OS 5?

??? I don't understand the question! I reply to the list because I've a
TG50 and I successfully mount the MS inside so the reply must be:
yes !
Eric Laly.

PS: I don't know a TG50 running with another OS than OS5 (but I could
be wrong...)

_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Clié and Linux Homepage:
http://kreucher.net/clie/

[Jason 'vanRijn' Kasper]

Post by Eric Laly

Post by Wong Khai Thye

Post by Wong Khai Thye
Hi,
Has anyone had any success with mounting the memory stick using

"MS

Post by Wong Khai Thye
Import" on the Sony Clie PEG-TG50?
On my system, I have the following errors in /var/log/messages

when I

[snip]

Post by Eric Laly

Post by Wong Khai Thye
and you have a Clie TG50, running Palm OS 5?

??? I don't understand the question! I reply to the list because I've a
yes !
Eric Laly.
PS: I don't know a TG50 running with another OS than OS5 (but I could
be wrong...)

I only wanted to clarify. I have an NX70V and this does not work for
me. It begs the question, therefore, as to which thing that is
different between your setup (OS5/TF50/2.4.21-ac4) and mine
(OS5/NX70/2.4.21-mdk25) that is the cause of this problem.

Does anyone have an NX70V working with usb-storage in linux?
--
,-----------------------------------------------------------------//
| Jason 'vanRijn' Kasper :: Numbers 6:22-26
`
| All brontosauruses are thin at one end, much MUCH thicker
| in the middle, and then thin again at the far end. That is
| the theory that I have and which is mine, and what it is too.
,
| bash$ :(){ :|:&};:
`----------------------//


_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Clié and Linux Homepage:
http://kreucher.net/clie/

[Eric Laly]

On 2003.09.27 16:33, Jason 'vanRijn' Kasper wrote:
...

Post by Jason 'vanRijn' Kasper
I only wanted to clarify. I have an NX70V and this does not work for
me. It begs the question, therefore, as to which thing that is
different between your setup (OS5/TF50/2.4.21-ac4) and mine
(OS5/NX70/2.4.21-mdk25) that is the cause of this problem.
Does anyone have an NX70V working with usb-storage in linux?

I think the only difference between our configs is the kernel.
I use a vanilla 2.4.21 patched with Alan Cox 'ac4' patch (not the
mandrake patches).
I've made a try with 2.4.22 but the visor support is broken on that
revision. Perhaps the usb-storage is working but as the hotsync doesn't
work, I didn't tried.

Regards.

Eric Laly.

_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Clié and Linux Homepage:
http://kreucher.net/clie/

[Greg KH]

Post by Eric Laly
I've made a try with 2.4.22 but the visor support is broken on that
revision.

"broken" how? There's a fix that I have pointed many people to on the
web, and is already in the 2.4.23-pre releases that some people have run
accross. What is the problem you are seeing?

thanks,

greg k-h

_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Cli� and Linux Homepage:
http://kreucher.net/clie/

[Eric Laly]

Post by Greg KH

Post by Eric Laly
I've made a try with 2.4.22 but the visor support is broken on that
revision.

"broken" how? There's a fix that I have pointed many people to on the
web, and is already in the 2.4.23-pre releases that some people have run
accross. What is the problem you are seeing?

I've attached a part of my log.

I just say that the support is 'broken' when I've made a try with
vanilla 2.4.22.

I've seen after there is a fix, but I don't go far as all is working
well in my system with 2.4.21-ac4.

Regards.

Eric Laly.

[John Thompson]

On Sun, 28 Sep 2003 09:39:19 +0200

(version gcc 3.3.2 20030812 (Debian prerelease)) #4 ven sep 5 20:57:32
CEST 2003

I see you're using a pretty bleeding-edge compiler here. Maybe if you
made your kernel/modules with an earlier version you might have better
luck.
--
-John (***@new.rr.com)

_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Cli� and Linux Homepage:
http://kreucher.net/clie/

[Eric Laly]

Post by John Thompson
On Sun, 28 Sep 2003 09:39:19 +0200

(version gcc 3.3.2 20030812 (Debian prerelease)) #4 ven sep 5

20:57:32

CEST 2003

I see you're using a pretty bleeding-edge compiler here. Maybe if you
made your kernel/modules with an earlier version you might have better
luck.

yes, but as I said before, it is working with 2.4.21-ac4 (with this
bleeding-edge compiler, I'm agreeing ;-) ) )... and I'm satisfied with
it!
The question was: 'Has anyone had any success with mounting the memory
stick using "MS Import" on the Sony Clie PEG-TG50?' and I just said
'yes' !

Regards.
Eric Laly.

_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Clié and Linux Homepage:
http://kreucher.net/clie/

[John Thompson]

On Sun, 28 Sep 2003 18:56:18 +0200

Post by Eric Laly

Post by John Thompson
On Sun, 28 Sep 2003 09:39:19 +0200
I see you're using a pretty bleeding-edge compiler here. Maybe if
you made your kernel/modules with an earlier version you might have
better luck.

yes, but as I said before, it is working with 2.4.21-ac4 (with this
bleeding-edge compiler, I'm agreeing ;-) ) )... and I'm satisfied
with it!
The question was: 'Has anyone had any success with mounting the memory
stick using "MS Import" on the Sony Clie PEG-TG50?' and I just said
'yes' !

Hokey-doke. I think I'll just toddle off now...
--
-John (***@new.rr.com)

_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Cli� and Linux Homepage:
http://kreucher.net/clie/

[Greg KH]

Post by Eric Laly

Post by Greg KH

Post by Eric Laly
I've made a try with 2.4.22 but the visor support is broken on that
revision.

"broken" how? There's a fix that I have pointed many people to on the
web, and is already in the 2.4.23-pre releases that some people have run
accross. What is the problem you are seeing?

I've attached a part of my log.
I just say that the support is 'broken' when I've made a try with
vanilla 2.4.22.

Yes, try 2.4.23-pre to fix this issue. It doesn't affect everyone
(2.4.22 works fine for me, and lots of other people.)

Post by Eric Laly
I've seen after there is a fix, but I don't go far as all is working
well in my system with 2.4.21-ac4.

Glad it works for you there.

greg k-h

_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Cli� and Linux Homepage:
http://kreucher.net/clie/

[John Thompson]

On Sat, 27 Sep 2003 20:06:34 +0200

Post by Eric Laly
I've made a try with 2.4.22 but the visor support is broken on that
revision. Perhaps the usb-storage is working but as the hotsync
doesn't work, I didn't tried.

Interesting. I have no problems with the visor support in 2.4.22. I use
an SJ20, but I don't think that should make a difference.
--
-John (***@new.rr.com)

_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Cli� and Linux Homepage:
http://kreucher.net/clie/

[david grant]

Post by Jason 'vanRijn' Kasper
I only wanted to clarify. I have an NX70V and this does not work for
me. It begs the question, therefore, as to which thing that is
different between your setup (OS5/TF50/2.4.21-ac4) and mine
(OS5/NX70/2.4.21-mdk25) that is the cause of this problem.
Does anyone have an NX70V working with usb-storage in linux?

Yes -- with RH9 and 2.4.22. It also worked with 2.4.21

---------------------------------------------------------------------------------------------------------------
David Grant

email: ***@david-grant.com
Tel: [phone]
Fax: [phone]
Mob: [phone]
---------------------------------------------------------------------------------------------------------------

[Jason 'vanRijn' Kasper]

Post by david grant

Post by Jason 'vanRijn' Kasper
I only wanted to clarify. I have an NX70V and this does not work for
me. It begs the question, therefore, as to which thing that is
different between your setup (OS5/TF50/2.4.21-ac4) and mine
(OS5/NX70/2.4.21-mdk25) that is the cause of this problem.
Does anyone have an NX70V working with usb-storage in linux?

Yes -- with RH9 and 2.4.22. It also worked with 2.4.21

wahoo!!! I just wanted to send out a good-news report!! I just updated
to 2.4.22-ac4 and now, I'm able to successfully mount the MS stick in my
NX70V Clie!!! Woot!!! =:) Whomever is responsible for this wonderful
piece of good news (be it Alan or the 2.4.22 guys, I'm not sure), I owe
you a virtual beer and a half!!
--
,-----------------------------------------------------------------//
| Jason 'vanRijn' Kasper :: Numbers 6:22-26
`
| All brontosauruses are thin at one end, much MUCH thicker
| in the middle, and then thin again at the far end. That is
| the theory that I have and which is mine, and what it is too.
,
| bash$ :(){ :|:&};:
`----------------------//



__________________________________________________________________________
Disclaimer: This e-mail message is intended only for the personal use of
the recipient(s) named above. If you are not an intended recipient, you
may not review, copy or distribute this message. If you have received this
communication in error, please notify us immediately by e-mail and delete
the original message.
This e-mail expresses views only of the sender, which are not to be
attributed to Rite Aid Corporation and may not be copied or distributed
without this statement.

_______________________________________________
clie-linux mailing list
clie-***@kreucher.net
http://kreucher.net/mailman/listinfo/clie-linux

Sony Clié and Linux Homepage:
http://kreucher.net/clie/